IRStookmySpyder
10-28-2007, 10:33 PM
I have been building this Intimidator for a couple months now, and I finally finished it and got to use it today. Some of these parts this was the first time seeing any use, which wasn't even much, not even 1 case of paint! The parts that this is the first time being used say like new. The 2k2 could use 3 things, but they aren't needed to use, just personal preference. I do accept trades, but don't long ball me. Well here are the specs...
2k2 Intimidator
Bob Long Assassins barrel
W.A.S. 2.7 board (Soon to be 2.9)
Hybrid Ultra-flow barbs and hoses
Hybrid Joint rail
Hybrid Adjustable ram cap (Like new, still have original box)
Smart parts on/off
Smart parts Ion regulator
Alias LPR
32 degrees gauge (Like new)
ANS ram
Empire poppet (Like new)
Lady eye covers
Things it could use:
LCD screen (You don't need one for a WAS 2.7, or 2.9 board since it is a LED board, but you could buy a new one if you want. It comes with one that doesn't have the ribbon to connect to the board.)
Membrane pad (You can use the trigger to change modes, but it would help if you had the LCD screen)
Grips (You don't need them, the clamshell acts as a grips, but if you want them you can buy them pretty cheap)
There is one thing wrong with this 2k2 that can't be fixed, it has a chip out of the front of the trigger frame. It was done from the previous owner, and it is where one of the screws are that holds on the side of the clamshell is, but it doesn't fall off or anything, the two I have in it work fine. Also the screw hole for another one of the side of the clamshell screws is messed up, it is too the side? It still works fine with only 2 screws, but I just wanted to post that so that everyone knows.
Pictures: http://i209.photobucket.com/albums/bb111/IRStookmySpyder/2k2%20Intimidator/2k2Intimidatorcloseup.jpg
http://i209.photobucket.com/albums/bb111/IRStookmySpyder/2k2%20Intimidator/2k2Intimidatorright.jpg
http://i209.photobucket.com/albums/bb111/IRStookmySpyder/2k2%20Intimidator/2k2Intimidatorleft.jpg
Trades:
Etek Ego (I add)
06 Ego (I add)
Mini (I add)
High-end guns
Cash:
$225 shipped and paypaled.
Rules:
Post here then PM me!
Paypal is preferred, but I do accept M.O.'s as well
Act mature
Don't flame
2k2 Intimidator
Bob Long Assassins barrel
W.A.S. 2.7 board (Soon to be 2.9)
Hybrid Ultra-flow barbs and hoses
Hybrid Joint rail
Hybrid Adjustable ram cap (Like new, still have original box)
Smart parts on/off
Smart parts Ion regulator
Alias LPR
32 degrees gauge (Like new)
ANS ram
Empire poppet (Like new)
Lady eye covers
Things it could use:
LCD screen (You don't need one for a WAS 2.7, or 2.9 board since it is a LED board, but you could buy a new one if you want. It comes with one that doesn't have the ribbon to connect to the board.)
Membrane pad (You can use the trigger to change modes, but it would help if you had the LCD screen)
Grips (You don't need them, the clamshell acts as a grips, but if you want them you can buy them pretty cheap)
There is one thing wrong with this 2k2 that can't be fixed, it has a chip out of the front of the trigger frame. It was done from the previous owner, and it is where one of the screws are that holds on the side of the clamshell is, but it doesn't fall off or anything, the two I have in it work fine. Also the screw hole for another one of the side of the clamshell screws is messed up, it is too the side? It still works fine with only 2 screws, but I just wanted to post that so that everyone knows.
Pictures: http://i209.photobucket.com/albums/bb111/IRStookmySpyder/2k2%20Intimidator/2k2Intimidatorcloseup.jpg
http://i209.photobucket.com/albums/bb111/IRStookmySpyder/2k2%20Intimidator/2k2Intimidatorright.jpg
http://i209.photobucket.com/albums/bb111/IRStookmySpyder/2k2%20Intimidator/2k2Intimidatorleft.jpg
Trades:
Etek Ego (I add)
06 Ego (I add)
Mini (I add)
High-end guns
Cash:
$225 shipped and paypaled.
Rules:
Post here then PM me!
Paypal is preferred, but I do accept M.O.'s as well
Act mature
Don't flame