INTIMIDATOR EYES & WIRING/barbs/o-rings/screws/lube/macro/fittings/gauges

[crankwalk]

Up for sale are various Timmy parts and other general maintenance items. Great for custom or Spimmy builders!

**Shipping is a flat rate fee for all items - PLEASE ADD $2.00 TO ALL ORDERS FOR SHIPPING.**

I do not accept trades. I accept PayPal, MO & cash.

BL Markers Wiring

* Alias/D2 battery harness ($10.00)



* Alias eye harness ($10.00)



* Intimidator eyes ($10.00 per eye - $17.00 per set)
All eyes allow for 20° of misalignment and are more powerful than stock eyes. O-rings included.



* 06/Gen4/Defiant 2 eyes ($20.00)
All 06 eyes allow for 20° of misalignment and are more powerful than stock eyes. O-rings included.



* 05 Wiring Combo ($32.00) - Save $5.00!!
Pick up a battery harness, eye harness, and a pair of eyes and save $5.00 over buying them separately.



Intimidator/D2 Barbs & Hose

* Nickel plated high flow barbs w/fiber washers ($2.75/ea)[/b]



If you can fit an .050" allen key through the barb, it is high flow. However, for maximum flow, you want a barb which will fit a 1/16" allen key (as pictured)! These are the same inner diameter as Hybrid "Hyper Flow" barbs, for max flow.

* Intimidator hi-flow hose ($1.00/ft)
High flow tubing for Intimidators. This is the same inner/outer diameter as Hybrid "Hyper Flow" hose that comes in their kits (this is larger than your stock Timmy hose).

* Autococker hose ($1.00/ft)
General purpose low pressure tubing for Autocockers and has slightly smaller ID/OD than the Intimidator hi-flow hose above. Can also be used to replace hose on Classic and 2k2 Timmys that have their original "standard flow" barbs installed.

O-Rings

* 2k2 o-ring kit - 1 complete marker rebuild, 1 ram bumper ($7.00)



This is the basic kit, but offers a complete replacement of all o-rings on your 2k2 Timmy.

Poppet•HPR Housing•LPR Housing•HPR Internals•LPR Internals•Reg Block•Ram•Ram Cap•Bolt•Ram Sleeve•Ram bumper

NOTE: Unlike some other kits for sale out there, these kits include genuine white teflon pin valve rings AND the correct OEM sized rings for the ram sleeve and reg housings. Contrary to what is listed in the 2k2 Bob Long manual, the proper ram sleeve o-rings are NOT correct and the sizes listed for the LPR/HPR housings are also wrong. The manual even fails to fully identify some necessary o-rings on the regs! Needless to say, the proper sizes are crucial to good air seals. While some other sellers carry bulk kits for many different markers and simply take the specs out of the manuals as correct, my kits are built from experience gained by building Timmys. Every o-ring in my kit will be a direct replacement, properly sized for your 2k2 parts listed above.

* Alias o-ring kit - 1 complete marker rebuild ($6.00)



Single rebuild for your Alias style marker.
NOTE: This does not include the "specialty" rings such as u-cup and square LPR ring, rather has fully compatible round o-rings as pictured.

* Gen4 (Empire 2 / Infamous / Ripper 3) o-ring kit - 1 complete marker rebuild ($6.00)
Single rebuild for your Gen4 marker.
NOTE: This does not include the "specialty" rings such as u-cups and square LPR ring, rather has fully compatible round o-rings (not yet pictured).

* O-ring pick ($2.50)
If you've ever had to remove the small poppet o-ring you will REALLY appreciate this item.

* Team Kit ($35.00)



The team kit includes enough o-rings for FIVE complete marker rebuilds (100+ o-rings!), five ram bumpers, 1oz of Dow 55 (or Dow 33 if you choose), 3/4 oz of Tri-Flow, and an o-ring pick. Comes packaged inside compartmented plastic box. Also, a diagram will be included so the correct o-rings can be found quickly and easily - no guesswork! Diagram will consist of actual o-ring locations (i.e. bolt o-rings, ram o-rings, etc) rather than vague sizes. Also available for Alias style markers.

Individual O-Rings & parts:

* individual teflon pin valve o-rings ($0.50/ea)
* individual ram sleeve & LPR o-rings ($0.50/ea)
* all other individual o-rings ($0.25/ea)
* Intimidator ram bumpers ($1.00/ea)
* Intimidator stiff (clear) detents - SOLD OUT


Macroline & Fittings



* Macroline ($1.00/ft)
High strength macro - your choice of black or translucent white.

* 90 degree swivel fittings ($4.00/ea)
* 90 degree non-swivel fittings ($3.00/ea)
* straight fittings ($3.00/ea)

Stainless Steel Screws

Replacement stainless steel screws for both 2k2 & Alias style markers. Replace your old worn out screws with these polished high strength stainless steel screws.
NOTE: the only screws NOT INCLUDED in the 2k2 kits are the ram sleeve set screw and trigger pivot screw (sold separately). The Alias kits *DO* come with all set screws (LPR & ram sleeve) but again, no trigger pivot screw.

* "Basic" 2k2 SS LCD screw kit - 15 screws, 3 washers ($7.00)
Included are Rubber grip screws•Trigger frame (clamshell halves) screws•LCD Trigger frame mounting screws•LPR block mounting screw•Eye cover screws•Three washers



NOTE: Washers may not be necessary to use in every situation, but I like to include them in my 2k2 kits.

* "Extended" 2k2 Clamshell SS screw kit - 15 screws, 1 o-ring ($9.00)
Included are Circuit board retaining screw WITH insulator o-ring•LCD screen screws•On/Off switch screws•Solenoid screw•Side plate screws•Trigger microswitch screws



This extended clamshell kit will replace every screw inside your 2k2 LCD clammy. It contains those small, hard to find, and finely threaded "specialty" screws that somehow manage to get lost over time or when buying used parts. Kit also comes with rubber o-ring for the circuit board screw, which serves as an electrical insulator. A very necessary but often overlooked item.

* "Complete" 2k2 SS screw kit ($15.00)
All screws and accessories listed in both the "Basic" and "Extended" kits.

* "Boxed" 2k2 SS screw kit ($21.00)
All screws and accessories listed in both the "Basic" and "Extended" kits, complete set of 6 hex keys for Timmys (includes the large regulator screw key, kits fit both 2k2 & Alias), packed in a sturdy plastic storage box with adjustable compartments. Also available for Alias style markers @ $17.00 per kit.



* "Complete" Alias SS screw kit - 18 screws, 1 o-ring ($10.00)
Included Rubber Grip Screws•Trigger Frame Screws•Trigger Frame Mounting Screws•Upper & Lower Circuit Board Retaining Screws (Lower w/insulating o-ring)•Eye Cover Screws•LPR Block & Ram Sleeve Set Screws (black).

NOTE: Most sellers don't include the larger set screws in their Alias kits! This is a COMPLETE kit to replace every screw on your Alias (Except trigger pivot screw, sold separately).

CHECK THE FIRST SECTION OF THE NEXT POST DOWN FOR INDIVIDUALLY PRICED SCREWS & INCLUDING AN ALIAS BLACKOUT KIT!

[crankwalk]

Individual Screws:

2k2:

* Rubber grip screws - 4 per marker ALSO FITS 2K5 ($0.50/ea)
* Trigger frame screws - 6 per marker ($0.50/ea)
* Trigger frame mounting screws - 2 per marker ($0.50/ea)
* LPR block mounting screw - 1 per marker ($0.50/ea)
* Eye cover screws - 2 per marker ALSO FITS 2K5 ($0.50/ea)
* Washers for LPR block and trigger frame screws ($0.50/ea)

* Circuit board retaining screw ALSO FITS 2K5 lower - 1 per marker ($0.50/ea)
* LCD screen screws - 3 per marker ($0.50/ea)
* On/Off switch screws - 2 per marker ($0.50/ea)
* Solenoid screw - 1 per marker ($0.75/ea)
* Side plate screws - 6 per marker ($0.50/ea)
* Trigger microswitch screws - 2 per marker ($0.75/ea)
* O-ring for circuit board screw ($0.25/ea)

* 2k2 Ram sleeve set screw - 1 per marker ($2.00/ea) DOES NOT COME IN ANY KIT.

Alias:

* Trigger frame screws - 6 per marker ($0.50/ea)
* Trigger frame mounting screws - 2 per marker ($0.50/ea)
* Upper circuit board screw - 1 per marker ($0.75/ea)
* LPR block set screw - 1 per marker ($1.00/ea)
* Alias Ram sleeve set screw - 1 per marker ($2.00/ea)

* Universal trigger pivot screw - fits 2k2 and 2k5 ($4.00/ea) DOES NOT COME IN ANY KIT.

Blackout Screw Kits

* Alias style blackout kit - $10.00
Includes grip panel, grip frame halves, frame-to-body mounting & eye cover screws



Hex Key Kits



Set of 6 hex keys, for 2k2 & Alias ($3.25)

Lubes



Economical sized o-ring lube, a small container will last you through many rebuilds.

* Dow 33 - Shocker/Ion Lube ($5.00/ea)
* Dow 55 - Timmy Lube ($5.00/ea)
* Tri-Flow - Timmy Bolt Lube ($2.50/ea)

Miscellaneous

* 100% Kevlar Sleeves - SOLD OUT
For those that like to go gloveless! Sleeves are made of 100% Kevlar fabric, dual layered thickness, are cut resistant and are washable. These particular sleeves have individual pre-cut fingers in order to provide coverage of the knuckles as well - unlike "other" popular cotton sleeves which may leave the fronts of your knuckles exposed since they are completely open in the front. Color is natural Kevlar yellow.



* Dual 9v Halo/Reloader B Mod ($3.00)
Convert your Halo/Reloader B from 6AA battery power to two smaller 9v batteries, reduce weight, and no longer worry about having to buy 9v for your marker and AA for your loader. All 9v mods are shrinkwrapped at the connections for best performance and durability.



* Black face 0-160psi mini gauge - SOLD OUT



* Black face 0-300psi mini gauge ($10.00)



* Black face CROSSFIRE 0-5000psi mini (HPA Tank) gauge - SOLD OUT



* Blue Loc-Tite ($2.50)



* Teflon tape - 50ft roll ($3.00)

[lastmanstanding]

I'm interested in some triflow, dow 55, and alias oring kit. could you do 11.75 for everything shipped? that's all I have in my Paypal. pm me please

[crankwalk]

lastmanstanding: PM sent

[anarchyintheua]

I was wondering if you might have an extra cupseal for a 2k2 timmy. Also i was wonder how much with shipping would a complete screw kit, a foot of high flow tubes, and i already have three barbs and i was wondering how many more would I need to finish up the job.

[crankwalk]

anarchyintheua: very sorry I don't sell 2k2 cupseals. i MAY have a used one floating around, chances are slim though. Sent you a PM on the other stuff..

[Alias2007]

Need another Alias black outkit..bottle of triflow and 4 of the dentents. PM me with the total please.

[crankwalk]

Alias2007: PM Sent!

[AirSin]

How accurate is the 0-300 psi gauge?

[crankwalk]

AirSin: Gauges are usually most accurate within the middle third of the scale. So unless you're going to be putting this gauge on a marker where you run between 100 and 200psi on the LPR, I'd suggest the 0-160psi gauge (where the range ~53psi-~106psi will be most accurate)